Cylindrical cased axial flow belt drive fans with motor located externally to the fan casing. The casing is made of sturdy welded sheet steel Fe 360 B hot galvanized with double flange and inspection door. The impeller and the hub are made of a die-cast aluminium alloy, with variable pitch angle, dynamically balanced. This construction includes belt guard. The drive components are totally insulated from the airflow. The sheet is painted following a cataforesis treatment + polyurethane paint. Working temperature -20ºC/180ºC.

Assembly systems
• ARRANGEMENT 9: belt drive with motor supported by the casing.
• ARRANGEMENT 12: belt drive with fan and motor supported by the baseframe. Only available for steel hub versions.

On request
• Manufactured in steel Fe 360B specially prepared to work until 300ºC continuously.
• Manufactured in Corten, for temperatures higher than 300ºC.
• Anticorrosive version in INOX AISI 304-316.
• Special sealed version for particular applications.

Motors
Voltage:
Three-phase 230/400V-50Hz

Other features
• Impeller-Motor (flow B).
• Motor-Impeller (flow A), on request.
• For sizes bigger than 1000, the fans are standard hot galvanized.
• From 1601 up to 1801 diameter, the hub is manufactured in steel.

Cylindrical cased axial flow belt drive fans with motor located externally to the fan casing. The casing is made of sturdy welded sheet steel Fe 360 B hot galvanized with double flange and inspection door. The impeller and the hub are made of a die-cast aluminium alloy, with variable pitch angle, dynamically balanced. This construction includes belt guard. The drive components are totally insulated from the airflow. The sheet is painted following a cataforesis treatment + polyurethane paint. Working temperature -20ºC/180ºC.

Assembly systems
• ARRANGEMENT 9: belt drive with motor supported by the casing.
• ARRANGEMENT 12: belt drive with fan and motor supported by the baseframe. Only available for steel hub versions.

On request
• Manufactured in steel Fe 360B specially prepared to work until 300ºC continuously.
• Manufactured in Corten, for temperatures higher than 300ºC.
• Anticorrosive version in INOX AISI 304-316.
• Special sealed version for particular applications.

Motors
Voltage:
Three-phase 230/400V-50Hz

Other features
• Impeller-Motor (flow B).
• Motor-Impeller (flow A), on request.
• For sizes bigger than 1000, the fans are standard hot galvanized.
• From 1601 up to 1801 diameter, the hub is manufactured in steel.

To provide fan assisted heating to workshops, commercial environments and it is also designed appliance for fireplace. It prepares the chimney for an effortless process of starting a fire.

Characteristics
IP20.
Made of steel sheet with a paint coating.
Quiet axial fan.
Switch ON/OF.
Adjustable support feet.
Rubber supports allowing to insert the FIRE FAN on the floor of a chimney.
Thermal protection.

Designed to be installed on the fans discharge side. The minimum air speed through the heater must be 1,5 m/s.
Maximum air temperature through the heater: 40ºC.
The heaters are fitted with:
– Armoured heating element.
– Double protection circuit to connect to the heater control circuit by means of a safety overheat automatic thermostat connected in series with another safety overheat manual reset thermostat (RESET).
– Wiring box IP43.
Available temperature sensors in the duct, ambient temperature sensors and speed controllers to complete the installation and to adjust the air temperature according to every need.

Designed to be installed on the fans discharge side.
The minimum air speed through the heater must be 2 m/s.
Maximum air temperature through the heater: 40ºC.
The heaters are fitted with:
– Armoured heating elements to connect to the three phase net (3×400).
– Double protection circuit to connect to the heater control circuit by means of a safety overheat automatic thermostat (60º), connected in series with another safety overheat manual reset thermostat (RESET).
– Wiring box IP43.
Available temperature sensors in the duct, ambient temperature sensors and speed controllers to complete the installation and to adjust the air temperature according to every need.
By means of this system the supplied air can reach up to 50º.
(See the electrical accessories section).

Designed for wall application in commercial or industrial environments.

Characteristics
Can be fitted up to a height of 10 metres.
High performance tangential propeller/impeller giving a low sound level.
Can be installed in series.

Designed for wall application in commercial or industrial environments.

Characteristics
Can be fitted up to a height of 5 metres.
High performance tangential impeller giving a low noise level.
Can be installed in series.
Available in ambient or ambient and hot air versions.

Designed for wall applications and fitted with a water coil to install in industrial environments.

Characteristics
Can be fitted up to a height of 5 metres.
High performance tangential propeller/impeller giving a low sound level.

Industrial air curtains fitted with water coils are specially recommended in those environments with a warm water heating system in which its easy to loose heat through open spaces.
Common applications in:
entrance goods doors, warehouse doors, halls, drying installations, greenhouses, workshops, etc…

The air curtains of the range S are especially designed to be installed in reduced spaces to create a barrier between two different areas.
Because of the volume/power ratio, they also fulfill a purpose as a heating element.
The range S is made up of two models of 4 and 6 kW respectively, both with two heating powers, two speeds and ambient thermostat.
They can also work at two speeds without heating.
They create an effective barrier up to a distance of 1.5 m.
The installation of this type of air curtain is recommended in cases such as kiosk windows, service windows that must be opened to assist the public, windows which, due to differences in temperature, have a tendency to steam up and make exterior vision difficult. Model COR-6-900 S includes a remote control unit.

Designed for wall application in commercial environments.

Characteristics
Can be fitted up to height of 3 meters.
Single phase motor with ball bearings and self-resetting thermal protector.
Equipped with centrifugal fans.
Output adjustable deflector.